This part of Indiana I live in is pretty flat. Dull, right? So I figure, why not have a volcano? Now… I get my magic drill machine that can drill as deep as I want it to drill.
If I drill a deep enough hole, say through the crust of the Earth, will it turn into a volcano?
That could actually work, since the hot material has a lower density and will thus be pushed out. But the hole needs to be somewhat big, since it will just solidify on the way up otherwise. So maybe 100 meter diameter?
Probably still won’t work unless there is serious overpressure in the area from some dynamic loading in the mantle. First off, no part of the mantle is naturally fluid at depth. The closest is the asthenosphere, at around 200 to 400 kn depth. This is still solid, but more like a soft wax. That too, the material is made of peroxides and has a density of between 5 to 15 percent higher than the granitic crust at depth and limestone that makes up the shallower crust of Indiana. Thus, it would be analogous to a whole in a wooden plank floating on a sea of dense soft wax…the wax won’t likely push through.
However, if you add water to the system while maintaining the heat, you can start to fluidize the gooey rock, and eventually it will reduce density enough to start creeping upwards. If you mix it deep enough and we’ll enough, you can start creating small steam bubbles within that will continue to grow as the rock ascends, further increasing the pressure (like a bubbly bottle of champagne). This will drive further upward pressures allowing for a surface eruption and formation of a volcano.
Source: am geophysicist and play(work) on volcanoes…just not in Indiana
deleted by creator
Yes, otherwise it is only sparkling lava.
You wouldn’t have much work here. Thanks for the expert information, I appreciate it!
If the lower layers are denser despite their much higher temperature and also super viscous, how can volcanos ever form? What if we drill right through this area with an even later size hole? In this caw tho, note that all of the back-pressure is missing at the hole, so gases would violently went to escape (10’000s of bar vs. 1 bar), which should be plenty of driving force to get stuff above the ground. Due to the outgassing the density should also massively decrease. Kind of like lowering a pipe into a volcanic lake that has CO2 dissolved in the deeper layers and letting that vent in a fountain.
Note that the pressure would go down, not up, as it ascends. But the volume would go up because of the lower pressure.
Still would be quite difficult. We think about 90% of accessing magma never makes it to the surface simply because it loses overpressure. It mostly comes down to how vicious the mama is and what it’s overall volatile content. All is which is dependent on the magma temperature, access to water, and silicate composition.
It’ll get more complex than that. I’m no expert, but I’m guessing you have to consider the depth of the crust at your location, type of soil and the distance from (and time since) the last closest volcanic eruption, possibly distance from the nearest tectonic boundary, maybe even tidal forces (assuming they have a considerable impact on magma being pushed out, but this may be a bit too far)
The closest eruption was the snag point I was thinking. We’re relatively near a fault line, but I don’t know of any volcanoes for a very, very long distance.
Of you’re talking new Madrid fault line in southern Illinois then you’re kinda close but a couple hundred-ish miles away even if you’re in Evansville Indiana area. I think the closest volcano is in Washington state to us.
Please don’t make a volcano in southern Indiana, my family in southern Illinois probably won’t enjoy being between a volcano and a major tectonic fault both lol
Edit: just to antagonize any Spaniards reading this, we don’t pronounce muh-drid like it should be, we say mad-rid here in southern Illinois. Fun stuff, idk why we screw it and Cairo both up
You don’t even want to know how people pronounce Terre Haute where I live.
Tear-ra hoe-te
Think I did that right but not sure on how to spell out how we say haute in a southern Illinois accent.
If you’re a Hoosier from south of Indianapolis then we likely speak very similarly
I hear “Terr Hoot” all the time. Why “hoot?” I have no idea.
Ah that one is different then
And it’s in Vigo county, which is either pronounced Vee-go or Vy-go. I’ve seen Ghostbusters 2, so I know how it’s pronounced
Oddly it’s the same in New Mexico, where people should know better. There’s a town between Santa Fe and Albuquerque called New MAD-rid.
Even worse since some level of Spanish should be understood by most everyone in the southwest lol
It was a mining town, so I thought that probably it was named/renamed by non-Hispanic Europeans. But why would they call it Madrid? So I have no idea.
Interesting. That’s not that big a diameter all things considered.